Small rice beater: is there any trick to the failure of rice beater?

Small rice beater: is there any trick to the failure of rice beater?

In the process of rice milling, if the rice mill is not properly adjusted, it is often easy to cause excessive broken rice and rice bran. So at this time, you should pay attention to strengthen the adjustment and maintenance of the rice milling machine, and eliminate all kinds of faults that affect rice processing in time. So, small rice milling machine: Is there any trick for rice milling machine faults?

Small rice beater: is there any trick to the failure of rice beater?

1. The adjustment method of not adjusting rice bran: adjust the fan speed to reach the rated speed of the rated speed; Adjust the air volume adjustment plate to increase the air volume; Tighten the fan pulley to eliminate belt slippage; Replace the fan impeller to ensure air volume, etc.

2. The method of increasing the particle content in rice: adjust the inlet gate, rice knife or press, rotate the rice knife, adjust the noodles or replace, and replace the lid.

3. Adjustment method of grain or chaff thickness in fine chaff: remove the contact surface between the cover and the chassis and lock the cover; Repair or replace the rice sieve, reintegrate women's clothing, adjust the windshield, increase the air volume and reduce the wind speed.

4. Reduction: adjust the white chamber pressure to ensure that the main shaft reaches the rated speed, replace the seriously worn roller, adjust the opening of the inlet and outlet gate, and dry the raw grain.

5. Transfer machine blockage and removal method: adjust the opening and outlet gate opening; Stop to check whether the screen hole is blocked. When there are too many things, clean them up; check the cause of belt slippage and eliminate them in time.

6. Rice Grain Unemployment Law: Replace Drum; The rice knife beside you, did you use it or replace it? Avoid mixing different varieties of raw grain together; Correctly adjust the inlet gate and the outlet gate.

7. Over-adjustment method: adjust the gap between the instrument and the opening of the discharge door to accumulate chaff; Re-adjust the speed of the drum; Dry the raw grain or spray a small amount of water to make the raw grain meet the drying requirements and the humidity meet the processing requirements; Check the rice sieve. Correctly guarantee the installation conditions.

8. No rice adjustment method: dry raw grain; Dredge ingredients, select raw grain, and remove sundries in raw grain; Dredge sieve holes; Contact.

small rice machine: common rice machine common fault is what?

1. Bran separation. Adjust the speed of the centrifugal fan to the rated speed, adjust the exhaust air volume adjustment plate, and increase the exhaust air volume; Tighten the heart-shaped fan belt plate and remove the conveyor belt buffer; Remove the centrifugal impeller to ensure the exhaust air volume; Whether the crank is tripped, whether the roller is separated from the turntable, and whether the spacing adjustment is appropriate; Check whether the vibrating screen is dropped.

2. Increase the flow of grain or rice in the fine bran. If you run vegetables or coarse chaff, you should delete WIDS and surface and stick to the range hood. Repair or remove the rice sieve; Reinstall and adjust the wind plate, increase the exhaust air volume and reduce the wind. If the amount of grain in the rice increases, adjust the inlet box, rice knife or pressure.

3. Reduce production. Adjust the pressure of the white chamber to ensure that the spindle bearing exceeds the rated speed ratio; replace the seriously damaged roller and adjust the opening degree of the export trade box plate again.

4. Rice machine block. Adjust the opening where the outlet is inserted; stop and check for obstructions. If you want to clear the obstacle, it can be unblocked, the entrance space can be accumulated, check the transmission belt, and remove it immediately.

5. The accuracy of millet particles is not appropriate. It is very simple to remove the roller; the rice knife is headed, the surface is adjusted, or the rice knife is disassembled; the mixing and mixing of different types of raw materials is prevented; the inlet box plate and the inlet box plate are properly adjusted.

6. Excess rice. Adjust the gap between the rice knife opening and the entrance box plate, and add up; adjust the speed ratio of the roller again; check the installation status of the material and the screen to ensure that the installation is correct.

7. Don't leave food, enter the entrance, choose the raw materials of the machine, and remove the dirt in the raw grain; the input of the round hole screen; the phase is in phase again, because the three-phase wire connector is wrong, it will not be able to reverse the rice condition.